首页

  • 11 Comments » for Photovoltaic Array
    1. Richa Richa says:

      Before some time I didn’t have much more knowledge about solar panel but before 2 or 3 yrs I have installed solar panel system in my 众鑫彩票注册’s top roof and that time I examined many companies and much researched on this. So I can say all about the solar PV system. A PV module is an assembly of photo-voltaic cells mounted in a frame work for installation. Photo-voltaic cells use sunlight as a source of energy and generate direct current electricity. A collection of PV modules is called a PV Panel, and a system of Panels is an Array. Arrays of a photovoltaic system supply solar electricity to electrical equipment.

    2. Krishnakumar.N Krishnakumar.N says:

      can i connect two strings in parallel with different voltage (20 Panels x30V =600V & 10 Panels x30V =300V) to a string monitoring Unit ( SMU) ?? if it connected what will be the voltage at common output terminal.

    3. marwa soliman marwa soliman says:

      Would you please send a formal quotation for the following item:

      The Solar Photovoltaic Array system

      Your quotation should include shipping till Cairo, delivery time and all your terms and conditions.

    4. floral floral says:

      Thanks for finally writing about >Photovoltaic Array or Solar Array uses PV Solar Panels <Loved it!

    5. Scott Scott says:

      ​HI there. Interesting read. I think I understand the logic. I live on a boat that has 4x Shell SM110-24 (rated output 110w; rated current 3.15A; rated voltage 35V). Becuase of the mast and boom these is often a shadow that passes over one or more of the panels – often leaving the other panels fully exposed to direct light. From what I read the shadow on one panel is likely to be affecting the performance of the whole array. It’s almost that I need each individual panel going back to the batteries individually – but thats a lot of wiring. What would be the best set up – series or parallel – and use of blockign diodes to minimise the impact of the shadow on one part of the array?. Cheers.

      • A series or parallel connection for your panels depends on your system requirements. These panels already have Bypass diodes built-in to prevent high currents from partial shading, but yes shading affects the performance and efficiency of the array.

        Blocking diodes prevent reverse currents from the battery to the panel when the panel is not generating electricity, for example night time. If you are using a charging regulator then blocking diodes are not normally require as it has protection built-in, only if you are charging batteries directly.

    6. farhan farhan says:

      dear sir,
      how to calculate maximum current in series connnection of pv array or pv panel??

    7. Capt.Waris Shaheen Capt.Waris Shaheen says:

      Dear Sir/Madam,
      Highly informative and concise artical on the subject. Great service to the electrical engineering community. Keep it up, God bless you with lot of wisdom and knowledge.
      Best regards.

    8. mohammed fayed mohammed fayed says:

      dear sir;
      how do calculate a solar cell to obtain an 20kw
      th`s
      mohammed

    1 Pings/Trackbacks for "Photovoltaic Array"
    1. Solar Array Project says:

      We will use photovoltaic cells that are provided in the lab to create an array. The cells will be connected using alligator clips, which are also provided. The cells will be linked in a circuit and attached first to an LED, then a rechargeable battery, and finally an i众鑫彩票注册Phone charger. LED and rechargeable batteries are also provided in lab, but we must purchase an i众鑫彩票注册Phone charger (which should cost no more than 10$). We hope to determine the most efficient way to maintain a strong current within the circuit especially when there is minimal light present.

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    *

    What's the Answer *